Greenheck Microprocessor Controller (474706 IOM) TAP v1.04 J Manuale Utente

1DDC Controller for Tempered Air ProductsReference Guide for the DDC ControllerPlease read and save these instructions. Read carefully before attempti

10DDC Controller for Tempered Air ProductsMenu Overviewa. Informationb. OverridesOn/Off UnitSetpointHeater LockoutLockout heater when outside above:

11DDC Controller for Tempered Air ProductsMenu OverviewPress PrgEsc to enter menus. c. BMS Configd. Service SettingsServiceManufacturerService Passwor

12DDC Controller for Tempered Air ProductsA. On/Off UnitB. SetpointThe controller is equipped with several menus to help guide users with altering p

13DDC Controller for Tempered Air ProductsThis screen displays The minimum and maximum supply air TemperaTure limiTs.This screen only appears if the u

14DDC Controller for Tempered Air Productsusers can choose eiTher The conTroller or The bms To deTermine su pply air seT poinT during operaTion.This s

15DDC Controller for Tempered Air ProductsE. Data LoggerThe clock screen allows The user To adjusT The Time and daTe.This screen allows The user To s

16DDC Controller for Tempered Air ProductsThe Overrides menu is for start-up, commissioning and troubleshooting. This menu allows the user to override

17DDC Controller for Tempered Air ProductsThis screen allows The user To override The heaTing operaTion.This screen only appears if a heating operatio

18DDC Controller for Tempered Air ProductsThis screen allows The user To enTer The i/o manual managemenT menu.The Manual Management menu allows the us

19DDC Controller for Tempered Air ProductsThis screen allows The user To adjusT bacneT msTp parameTers.This screen only appears if the selected BMS pr

2DDC Controller for Tempered Air ProductsSequence of Operation . . . . . . . . . . . . . . . 2General Operation . . . . . . . . . . . . . . . . 2Set

20DDC Controller for Tempered Air ProductsThis screen allows The user To quickly enable The bms To conTrol uniT operaTion.This screen appears if the u

21DDC Controller for Tempered Air ProductsH. Manufacturera. ConfigurationConfiguration menu allows the user to change the setup code for the unit, en

22DDC Controller for Tempered Air ProductsThis screen allows The adjusTmenT of parameTers for The economizer funcTion.This screen only appears if an e

23DDC Controller for Tempered Air ProductsThis screen displays The compressor minimum on and off Times.This screen only appears if DX cooling was prov

24DDC Controller for Tempered Air ProductsThis screen allows adjusTmenT of The fan airflow proving swiTch Time delay.Since the unit is only part of a

25DDC Controller for Tempered Air ProductsThis screen allows adjusTmenT of The Time del ay before The exhausT fan when The supply fan sTarTs.This scre

26DDC Controller for Tempered Air ProductsModbus-RTU/TCP/IP Network Address: 1BACnet IP/Ethernet BACnet MSTP Device Instance: 77000(default)LonWorks F

27DDC Controller for Tempered Air ProductsThe pCOe is an Auxiliary I/O module that can be used to monitor additional statuses within the unit. The pCO

28DDC Controller for Tempered Air ProductsDisplay is hard to read.Unit Controller Display: Hold PrgEsc ESC and Prg Esc ENTER at the same time, while

29DDC Controller for Tempered Air ProductsParameter Factory Minimum MaximumDevice Instance 77000 0 4194303Station Address 0 0 127Max Master 127 0 127M

3DDC Controller for Tempered Air Products3Sequence of Operation - Unoccupied cooling is enabled when the room temperature is greater than the unocc

30DDC Controller for Tempered Air Products*The BACnet IP/Eth card is configured for DHCP from the factory.To view the current parameters, go the BMS C

31DDC Controller for Tempered Air ProductsMaintenance LogDate __________________ Time _____________ AM/PMNotes:_______________________________________

32474706•DDCController,Rev.3,June2011 Copyright2011©GreenheckFanCorporationGreenheck warrants this equipment to be free from defects in m

4DDC Controller for Tempered Air ProductsAlarmsThe DDC controller includes a digital output for remote indication of an alarm condition. Possible alar

5DDC Controller for Tempered Air ProductsController OverviewJ1J1 J24J24J14J14J11J11J15J15J2J2 J5J5J4J4J3J3service cardRx-/Tx-Rx+/Tx+GNDC1NO1NO2NO3C1C4

6DDC Controller for Tempered Air ProductsThe DDC controller is located in the unit control panel. The face of the controller has six keys, allowing th

7DDC Controller for Tempered Air ProductsExamples of AlarmsIf an alarm occurs, the Prg Esc button will glow red on the controller and the remote displ

8DDC Controller for Tempered Air ProductsThe DDC controller will revert to a default main menu loop. This loop includes several screens to view the op

9DDC Controller for Tempered Air ProductsHeating StatusHeater Control: 000% Hot Gas Reheat: 000% Staged reheat is: ON Compressor: 1 2STATUS LINEP